Siemens 6ES7156-0AA01-0XA0 DP/AS-i Link Coupler

Het item werd toegevoegd aan uw offerteaanvraag
Product Information
The Siemens 6ES7156-0AA01-0XA0 Adaptor : DP-ASI link is a SIMATIC DP communication module that connects PROFIBUS DP controllers with AS-Interface actuator-sensor networks. It provides gateway communication between the PROFIBUS DP control network and the AS-Interface bus, allowing compatible SIMATIC S5 and S7 automation systems to integrate AS-Interface field devices. The module operates from a 24 V DC supply and has an IP67-rated housing for appropriately protected field installations.
The coupler has a built-in PROFIBUS DP fieldbus uplink with 2 x 12-pin device connectors and supports PROFIBUS DP communication rates up to 12 Mbit/s. The AS-Interface connection is integrated into the module. Replacement commissioning is performed through Siemens STEP 7 using the host automation controller; the PROFIBUS DP address, AS-Interface slave parameters and existing hardware configuration must match the machine project before the configuration is downloaded.
For troubleshooting, PROFIBUS DP network diagnostics are accessed through the master PLC and the STEP 7 diagnostic view. During replacement, check the 24 V DC supply, PROFIBUS DP connections, AS-Interface connection, bus addressing and the STEP 7 hardware configuration. The 6ES7156-0AA01-0XA0 is discontinued and is used for repair, maintenance and extension of established Siemens fieldbus installations, where a used or refurbished spare may be required.
Technical Specifications
| Manufacturer | Siemens |
| Part number | 6ES7156-0AA01-0XA0 |
| Model/type | Adaptor : DP-ASI link |
| Component type | Communication module |
| Product family | SIMATIC DP |
| Supply voltage | 24 V DC |
| PROFIBUS DP interface | Built-in fieldbus uplink with 2 x 12-pin device connectors |
| PROFIBUS DP data rate | Up to 12 Mbit/s |
| AS-Interface connection | Built-in actuator-sensor bus interface |
| Supported protocols | PROFIBUS DP and AS-Interface |
| Configuration software | STEP 7 |
| Protection rating | IP67 |
| Lifecycle status | Discontinued |
Programming and Configuration
Configuration and parameterization are carried out with Siemens STEP 7 through the host automation controller. The existing STEP 7 hardware configuration is used to define the PROFIBUS DP integration and the connected AS-Interface network.
When installing a replacement, match the PROFIBUS DP address and AS-Interface slave parameters to the machine project, then download the hardware configuration through STEP 7. The spare must be commissioned with the same project settings before it can operate as part of the established system.
Communication and System Integration
The Siemens 6ES7156-0AA01-0XA0 links a PROFIBUS DP master network to an AS-Interface actuator-sensor network. Its PROFIBUS DP interface is a built-in fieldbus uplink with 2 x 12-pin device connectors and supports communication rates up to 12 Mbit/s.
The AS-Interface bus connection is integrated into the coupler, providing a single communication module for the two bus systems. The unit is intended for integration with Siemens SIMATIC S5 and S7 automation environments using PROFIBUS DP and AS-Interface.
Diagnostics and Status Indication
PROFIBUS DP network diagnostics are available through the master PLC and the STEP 7 diagnostic view. These tools support checks of the coupler within the host automation system and its PROFIBUS DP network connection.
For a replacement unit, first check the 24 V DC supply, PROFIBUS DP and AS-Interface connections, bus addressing and the STEP 7 hardware configuration. The physical installation should also maintain the conditions required for the IP67 protection rating.
Replacement and Spare Part Considerations
Replacement identification should begin with the exact Siemens part number 6ES7156-0AA01-0XA0 and the Adaptor : DP-ASI link model/type. Compatibility also depends on the existing SIMATIC S5 or S7 installation, PROFIBUS DP master network, AS-Interface network and STEP 7 project.
Before commissioning a spare, match the PROFIBUS DP address, AS-Interface slave parameters and hardware configuration to the machine project. Confirm the 24 V DC supply, both bus connections and the physical installation. This discontinued module is primarily used for maintenance, repair and extension of established fieldbus systems, with used or refurbished units serving as replacement options.
Frequently Asked Questions
What does the Siemens 6ES7156-0AA01-0XA0 do?
The 6ES7156-0AA01-0XA0 is a SIMATIC DP communication module that connects a PROFIBUS DP control network with an AS-Interface actuator-sensor network.
Which Siemens systems can use this DP/AS-i link coupler?
The coupler is intended for Siemens SIMATIC S5 and S7 automation environments using PROFIBUS DP and AS-Interface.
Which software is used to configure the 6ES7156-0AA01-0XA0?
Configuration and parameterization are performed with Siemens STEP 7 through the host automation controller.
What must be transferred or checked when replacing this coupler?
The replacement must match the existing STEP 7 hardware configuration, PROFIBUS DP address and AS-Interface slave parameters. The 24 V DC supply and both bus connections should also be checked.
What PROFIBUS DP speed does this module support?
The built-in PROFIBUS DP interface supports communication rates up to 12 Mbit/s.
How are network diagnostics accessed?
PROFIBUS DP network diagnostics are accessed through the master PLC and the STEP 7 diagnostic view.
Take advantage of our exchange formula
A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.
Play it safe with our warranty conditions
Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.
Data backup and recovery
Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.
Specific firmware and hardware versions
If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.
Disclaimer:
We are not an authorised distributor of Siemens.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.



