Siemens 6ES7151-1AA05-0AB0 IM151-1 ET 200S Interface Module

New 
On request
Refurbished   
10+ available within 4 - 6 business days
Want to exchange a faulty product?
Receive a discount on your purchase when you turn in a faulty product. Upon receipt, we will check the product to determine its eligibility according to the terms and conditions.
Repair  
Available
We can repair this product for you.
 

Product Information

Product Family: SIMATIC DP / ET 200S

The Siemens 6ES7151-1AA05-0AB0, also identified as the IM 151-1 Standard, is a PROFIBUS DP interface module for the SIMATIC DP / ET 200S distributed I/O system. It connects an ET 200S station containing digital and analog I/O modules to a PROFIBUS DP master, allowing the remote I/O to exchange process data with a PLC or automation controller. The module provides an integrated RS-485 interface through a 9-pin Sub-D female connector and is supplied with the termination module required for the ET 200S station assembly.

For a replacement unit, the installed ET 200S configuration, PROFIBUS address and connected terminal, power and I/O modules must match the existing station design. The PROFIBUS DP master transfers the station parameters at startup, while Siemens STEP 7 and HW Config are used for hardware configuration, parameterization and diagnostics. The interface supports DP V0 and DP V1 communication as a slave at transmission rates up to 12 Mbit/s. The termination module must be installed at the end of the station assembly before commissioning.

The IM 151-1 Standard supports up to 63 connected I/O modules, with 244 bytes of input address space and 244 bytes of output address space. During troubleshooting, check the PROFIBUS address settings, the RS-485 bus connection, the master configuration and the termination module installation. A failed interface module interrupts communication with the ET 200S station, making a correctly configured spare or tested exchange unit relevant for restoring an existing installation. This Siemens module is discontinued and is used for maintenance and replacement of established ET 200S systems.

Technical Specifications

ManufacturerSiemens
Part number6ES7151-1AA05-0AB0
Model/typeIM 151-1 Standard
Component typePROFIBUS DP interface module
Product familySIMATIC DP / ET 200S
PROFIBUS DP device roleSlave
Bus interfaceRS-485 via 9-pin Sub-D female connector
PROFIBUS DP protocol versionsDP V0 and DP V1
Maximum PROFIBUS DP transmission rate12 Mbit/s
PROFIBUS DP vendor ID806Ah
Maximum connectable I/O modules63 modules
Input address space244 byte
Output address space244 byte
Maximum station width2 m
Maximum input current200 mA
Typical power loss3.3 W
Mains buffering time20 ms
PROFIBUS DP output current80 mA
Isochronous modeNot supported
Included componentET 200S termination module
LifecycleDiscontinued

Programming and Configuration

Siemens STEP 7 and HW Config provide the engineering environment for configuring and parameterizing the IM 151-1 Standard in an ET 200S station. The PROFIBUS DP master downloads the station parameters at startup, and the hardware configuration must reflect the connected ET 200S terminal modules, power modules and I/O expansion modules.

When commissioning a spare, transfer the established hardware configuration to the replacement installation and verify the PROFIBUS address before startup. The configured station can contain up to 63 I/O modules and provides 244 bytes of input address space together with 244 bytes of output address space.

Communication and System Integration

The IM 151-1 Standard connects the ET 200S station to a PROFIBUS DP master through an integrated RS-485 interface and a 9-pin Sub-D female connector. It operates as a PROFIBUS DP slave and supports DP V0 and DP V1 protocol versions.

Communication rates are supported up to 12 Mbit/s. For system integration or replacement, match the PROFIBUS address, master configuration and connected ET 200S module assembly. The termination module supplied for the station assembly must be installed at the end of the ET 200S station.

Diagnostics and Status Indication

Diagnostics and parameterization are performed through Siemens STEP 7 and HW Config. The PROFIBUS DP master downloads the station parameters at startup, providing the configuration basis for communication with the ET 200S station.

For first-line troubleshooting, verify the PROFIBUS address settings, the RS-485 connection, the master hardware configuration and the installation of the termination module. These checks are particularly relevant after replacing the IM 151-1 Standard in an existing ET 200S assembly.

status_leds

Replacement and Spare Part Considerations

Use the exact Siemens part number 6ES7151-1AA05-0AB0 and model IM 151-1 Standard when identifying a replacement for an existing unit. Before installation, compare the PROFIBUS address, the configured ET 200S station structure and the connected terminal, power and I/O modules with the existing system.

A replacement is not simply a mechanical exchange: the PROFIBUS master configuration and station parameters must correspond to the installed ET 200S assembly. Confirm the RS-485 bus connection and install the supplied termination module at the end of the station before commissioning.

This discontinued interface module is intended for repair and spare-part maintenance of established Siemens ET 200S installations. When an interface fault interrupts remote I/O communication, a correctly configured spare or tested exchange unit can support the return of the station to service.

Frequently Asked Questions

What is the Siemens 6ES7151-1AA05-0AB0?

The 6ES7151-1AA05-0AB0 is the Siemens IM 151-1 Standard PROFIBUS DP interface module for the SIMATIC DP / ET 200S distributed I/O system.

Which PROFIBUS interface and protocols does the IM 151-1 use?

It uses an integrated RS-485 interface with a 9-pin Sub-D female connector and supports PROFIBUS DP V0 and DP V1 as a slave, at transmission rates up to 12 Mbit/s.

How many I/O modules can the ET 200S station support with this interface module?

A single station can accommodate up to 63 connected I/O modules, with 244 bytes of input address space and 244 bytes of output address space.

Which software is used to configure and diagnose the IM 151-1 Standard?

Siemens STEP 7 and HW Config are used for hardware configuration, parameterization and diagnostics. The PROFIBUS DP master downloads the station parameters at startup.

What should be checked before commissioning a replacement?

Check that the PROFIBUS address, master configuration, connected ET 200S modules, RS-485 connection and termination module installation match the existing station design.

Is the Siemens 6ES7151-1AA05-0AB0 still an active product?

The 6ES7151-1AA05-0AB0 is discontinued and is used as a maintenance and replacement part for established Siemens ET 200S installations.

Take advantage of our exchange formula

A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.

Play it safe with our warranty conditions

Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.​​​​​​​

Data backup and recovery

Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.

Specific firmware and hardware versions

If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.


Disclaimer:
We are not an authorised distributor of Siemens.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.