Mitsubishi MR-J3-10A-S030 Plastcontrol AC Servo Drive

New 
On request
Refurbished   
On request
Want to exchange a faulty product?
Receive a discount on your purchase when you turn in a faulty product. Upon receipt, we will check the product to determine its eligibility according to the terms and conditions.
Repair  
Available
We can repair this product for you.
 

Product Information

Product Family: MELSERVO-J3 | Series: MR-J3-A

The Mitsubishi MR-J3-10A-S030PLASTCONTROLVERSION is a Melservo MR-J3 Plastcontrol version AC servo drive and amplifier from the MELSERVO-J3 family and MR-J3-A series. It provides 0.1 kW (100 W) rated output power for compact motion-control applications and operates in the 200-230 V AC supply class. The drive uses sine-wave PWM control with a current control system and is intended for existing Plastcontrol equipment using Mitsubishi MELSERVO-J3 servo technology.

Replacement commissioning requires more than matching the basic MR-J3-10A designation. The -S030 Plastcontrol variant must be matched to the machine configuration, including the original parameter set, firmware behavior and I/O assignment. MR Configurator provides parameter setting, monitoring, test operation, diagnostics, backup and restoration through the built-in USB Mini-B PC interface or RS-422 serial interface. The drive has 11 digital inputs, 5 digital outputs, 3 analog inputs and 2 analog outputs for machine-control integration, so the replacement wiring and configured functions must correspond to the original unit.

The integrated 7-segment LED displays operating status, warning codes and alarm codes. MR Configurator can also provide software status monitoring and access to diagnostic functions through USB or RS-422. Series fault codes include supply, memory, encoder, board, main-circuit, regenerative, speed, current, voltage, overload, parameter and position-deviation conditions. Internal memory, clock or control-board faults can require repair or replacement of the drive, while supply, encoder, motor wiring, regenerative circuit and machine-load checks can help isolate external causes before an exchange unit is commissioned.

Technical Specifications

ManufacturerMitsubishi
Part numberMR-J3-10A-S030_PLASTCONTROL_VERSION
Model/typeMelservo MR-J3: Plastcontrol version
Component typeAC servo drive/amplifier
Product familyMELSERVO-J3
SeriesMR-J3-A
Lifecycle statusDiscontinued
Rated output power0.1 kW
Rated current1.1 A
Supply voltage200-230 V AC
Control methodSine-wave PWM control with current control system
Digital inputs11
Digital outputs5
Analog inputs3
Analog outputs2
Built-in serial interfaceRS-422
PC setup interfaceUSB Mini-B
Communication protocolRS-422 serial communication
Status indication7-segment LED

Programming and Configuration

Mitsubishi MR Configurator is used for parameter setting, monitoring, test operation, diagnostics, parameter backup and parameter restoration. The PC connects to the servo amplifier through the built-in USB Mini-B interface or the RS-422 serial interface.

Before commissioning a replacement, transfer or restore the original machine parameter set and confirm that the configured functions match the Plastcontrol installation. The -S030 OEM designation is important because a standard MR-J3-10A may not contain the required OEM parameters, firmware behavior or I/O assignments.

A valid parameter backup reduces commissioning risk, but the restored configuration must still be checked against the replacement wiring and the machine's original drive setup.

Communication and System Integration

The servo amplifier provides a built-in RS-422 serial interface for communication and a USB Mini-B PC setup interface. MR Configurator uses these connections for parameter access, monitoring, test operation and diagnostics.

Machine-control integration is supported by 11 digital inputs, 5 digital outputs, 3 analog inputs and 2 analog outputs. The available I/O is suited to the configured control functions of the Plastcontrol installation, including pulse and analog control arrangements.

When replacing the unit, check the connector wiring, I/O assignment and configured parameter set against the original MR-J3-10A-S030 Plastcontrol version before applying the machine control signals.

Diagnostics and Status Indication

The 7-segment LED displays the drive operating status, warning codes and alarm codes. Diagnostic access is also available through the MR Configurator diagnostic menu and software status monitoring over USB or RS-422.

For a fault investigation, use the displayed alarm or warning code together with the relevant external checks. Supply voltage and wiring, encoder cable connections, motor wiring, grounding and shielding, regenerative components, parameter values and mechanical load are relevant checks for the corresponding MR-J3 series alarms. Internal memory, clock and control-board faults may require repair or replacement of the drive.

Status LED Indicators

LEDColor/StatusMeaning
7-segment LEDDisplays drive operating status, warning codes, and alarm codes. Internal board errors may display hardware failure codes requiring repair or replacement.

Replacement and Spare Part Considerations

This discontinued MR-J3-10A-S030 Plastcontrol version is intended for service replacement and maintenance of existing Mitsubishi MELSERVO-J3 installations. Match the complete part number, including the -S030 OEM designation, rather than selecting a standard MR-J3-10A solely by rated power.

Before commissioning a spare, compare the original drive configuration, firmware behavior, parameter set, I/O assignment, motor and encoder arrangement, and interface wiring. Restore the original parameters with MR Configurator through USB Mini-B or RS-422, then check that the configured inputs and outputs correspond to the machine wiring.

AL 12, AL 13, AL 15 and AL 17 indicate internal memory, clock or board-related conditions for which repair or a replacement drive is relevant. ABC Industrial Parts can support repair or exchange preparation when the original unit requires a compatible spare and configuration transfer.

Error Codes & Fault Codes

The following error codes may be displayed during operation or diagnostics:

CodeNameDescriptionPossible CauseRecommended Action
AL 10UndervoltageMain circuit power supply voltage dropped below the allowable limit.Low input voltage, power supply failure, or insufficient power capacity.Check the main circuit power supply voltage and wiring.
AL 12Memory Error 1Internal memory RAM or EEPROM read/write failure.Internal component failure or memory fault.Replace the unit or return it for repair.
AL 13Clock ErrorInternal printed circuit board clock error.Internal hardware failure.Contact service or replace the unit.
AL 15Memory Error 2Internal EEPROM fault.Faulty internal memory hardware.Return the unit for repair.
AL 16Encoder Error 1Communication failure between the encoder and servo amplifier.Disconnected or faulty encoder cable, or defective encoder.Check encoder cable connections, pinout, and shielding.
AL 17Board ErrorInternal CPU or control-board hardware fault.Control board malfunction or damaged internal circuitry.Replace the drive unit.
AL 20Encoder Error 2Encoder communication data fault or signal interruption.Noise interference on the encoder line or damaged encoder cable.Verify encoder cable grounding and shield connections.
AL 24Main Circuit ErrorGround fault or output short circuit detected in the main power stage.Motor power-line insulation breakdown or shorted output phase.Check motor wiring and measure motor insulation resistance.
AL 30Regenerative Option ErrorRegenerative discharge transistor or resistor thermal overload.Excessive braking energy, incorrect parameter setting, or broken braking-option wiring.Check regenerative duty cycle, braking resistor value, and wiring.
AL 31OverspeedServo motor speed exceeded the allowable maximum.Speed command overshoot, incorrect motor parameter, or feedback instability.Check the speed command signal and acceleration/deceleration settings.
AL 32OvercurrentOutput current exceeded the maximum instantaneous threshold.Short circuit in motor wiring, damaged output power module, or excessive acceleration/deceleration.Disconnect motor output cables to test the drive. If the alarm persists at power-up, replace the unit.
AL 33OvervoltageMain-circuit DC bus voltage exceeded the maximum limit.High input AC supply voltage or inadequate regenerative absorption.Verify line input voltage and external regenerative resistor sizing.
AL 37Parameter ErrorA parameter value is outside the valid range or forms an invalid combination.Incorrect parameter download or invalid parameter modification.Check and re-enter the default parameter set or restore a valid backup file.
AL 50Overload 1Continuous current overload exceeded the drive or motor thermal rating.Mechanical overload, machine jam, or motor capacity that is too small.Check the mechanical load for binding and reduce the duty cycle if necessary.
AL 51Overload 2Severe instantaneous overload detected.Mechanical shock load or rapid stall condition.Check machine operation and load profile.
AL 52Error ExcessivePosition deviation error counter exceeded its parameter threshold.Locked motor, excessive load, incorrect gain tuning, or encoder wiring problem.Check motor rotation, mechanical linkage, and position-loop gain.

Frequently Asked Questions

What is the Mitsubishi MR-J3-10A-S030_PLASTCONTROL_VERSION?

It is a 0.1 kW (100 W) Mitsubishi Melservo MR-J3 Plastcontrol version AC servo drive and amplifier in the MELSERVO-J3 family and MR-J3-A series, with a 200-230 V AC supply class.

Can a standard MR-J3-10A replace the MR-J3-10A-S030 Plastcontrol version?

A standard MR-J3-10A should not be selected by rating alone. The -S030 designation identifies the Plastcontrol OEM variant, so the original parameters, firmware behavior, I/O assignment and machine wiring must be matched before replacement.

Which software and interfaces are used to configure this servo amplifier?

Mitsubishi MR Configurator is used for parameter setting, monitoring, test operation, diagnostics, backup and restoration. The connection can be made through the built-in USB Mini-B PC interface or RS-422 serial interface.

How does the MR-J3-10A-S030 display alarms?

The integrated 7-segment LED displays operating status, warning codes and alarm codes. MR Configurator also provides a diagnostic menu and software status monitoring through USB or RS-422.

What should be checked for an AL 16 encoder alarm?

Check the encoder cable connections, pinout and shielding. AL 16 indicates a communication failure between the encoder and servo amplifier.

When is repair or exchange relevant for this servo drive?

Internal memory, clock and control-board faults such as AL 12, AL 13, AL 15 and AL 17 can require repair or replacement. External causes such as supply voltage, encoder wiring, motor wiring, regenerative components, parameters and mechanical load should be checked for the corresponding alarms.

Take advantage of our exchange formula

A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.

Play it safe with our warranty conditions

Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.​​​​​​​

Data backup and recovery

Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.

Specific firmware and hardware versions

If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.


Disclaimer:
We are not an authorised distributor of Mitsubishi.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.