Siemens C98043-A7001-L2-4 SIMOREG CUD1 Control Module

New 
On request
Refurbished   
10+ available within 4 - 6 business days
Want to exchange a faulty product?
Receive a discount on your purchase when you turn in a faulty product. Upon receipt, we will check the product to determine its eligibility according to the terms and conditions.
Repair  
Available
We can repair this product for you.
 

Product Information

Product Family: SIMOREG | Series: 6RA70

The Siemens C98043-A7001-L2-4 is an ELEKTRON. CONTR. C98043-A7001-L2 control module with terminal, also identified as a CUD1 control electronics assembly. This internal plug-in control board is used in Siemens SIMOREG DC MASTER 6RA70 series converters, where it supports internal control and regulation electronics for armature and field current regulation. The L2-4 variant includes the associated terminal configuration and is installed through a backplane edge connector and terminal block interface.

A replacement C98043-A7001-L2-4 must match the installed SIMOREG hardware variant, internal wiring, terminal configuration and firmware requirements. The unit is intended for service replacement within the converter rather than general-purpose standalone operation. Before removing the existing board, back up the SIMOREG parameters where possible. After installation, the parameter set can be restored or re-entered with an OP1S operator panel, DriveMonitor or SIMOVIS software, followed by parameterization and commissioning.

The SIMOREG 6RA70 PMU or OP1S keypad display provides access to drive status, faults and alarms, while DriveMonitor and SIMOVIS support diagnostics and commissioning. Troubleshooting can include checking the armature and field circuits, feedback wiring, supply phases, board seating, backplane connector integrity and communication parameters, depending on the displayed fault. Since this Siemens control module is obsolete and end of life, a compatible repair or tested exchange unit can help maintain an installed legacy DC drive without replacing the complete converter.

Technical Specifications

ManufacturerSiemens
Part numberC98043-A7001-L2-4
Model/typeELEKTRON. CONTR.C98043-A7001-L2 INCL. TERMINAL
Component typeIndustrial electronic control module
Product familySIMOREG
SeriesSIMOREG 6RA70
Control functionInternal control and regulation electronics for armature and field current regulation
Installation typeInternal plug-in control board assembly
Internal communication interfaceInternal serial bus
Internal connectorBackplane edge connector and terminal block interface
Included terminalIncluded
Lifecycle statusObsolete / end of life

Programming and Configuration

The SIMOREG 6RA70 parameter set can be restored or entered after fitting the replacement control module. An OP1S operator panel, DriveMonitor or SIMOVIS software can be used for parameterization and commissioning.

A spare is not necessarily ready for operation immediately after installation. Match the C98043-A7001-L2-4 L2-4 hardware variant, terminal configuration and firmware requirements, then transfer or re-enter the drive parameters before returning the converter to service.

Communication and System Integration

The control module communicates with the converter's main controller through an internal serial bus. Its internal connection uses a backplane edge connector and terminal block interface, making the connector arrangement and terminal configuration important when selecting a replacement.

The SIMOREG 6RA70 drive can be commissioned and diagnosed through an OP1S operator panel, DriveMonitor or SIMOVIS software. Communication-related faults can also involve the serial interface board, board seating, backplane connector integrity or interface parameters.

Diagnostics and Status Indication

Drive status, faults and alarms can be read on the SIMOREG 6RA70 PMU or OP1S keypad display. DriveMonitor and SIMOVIS provide additional parameterization, commissioning and troubleshooting functions, including access to drive fault and alarm information.

For a communication-related problem, check that the board is seated correctly, inspect the backplane connector and pins, and verify the communication interface parameters. Other first-line checks depend on the displayed fault and may include the armature circuit, field wiring, feedback channel, supply phases, cooling fan and ventilation.

Replacement and Spare Part Considerations

Use the complete Siemens part number C98043-A7001-L2-4 when identifying a replacement. Confirm that the installed converter is from the SIMOREG DC MASTER 6RA70 series and that the L2-4 hardware variant, internal wiring, terminal configuration, connector arrangement and firmware requirements match the replacement board.

Back up the existing SIMOREG parameters before board removal where possible. After fitting the spare, restore or re-enter the parameters with an OP1S operator panel, DriveMonitor or SIMOVIS, then complete commissioning and review the drive fault and alarm information. ABC Industrial Parts can support repair or exchange requirements for this obsolete control module.

Error Codes & Fault Codes

The following error codes may be displayed during operation or diagnostics:

CodeNameDescriptionPossible CauseRecommended Action
F001Armature overcurrentThe armature current has exceeded the permissible limit.Motor overload, current limit parameter set too high, short circuit, or ground fault in the armature circuit.Check motor load conditions, verify current limit parameter settings, and inspect the armature circuit for short circuits or ground faults.
F002Overvoltage in DC link or armature circuitVoltage has exceeded the permissible threshold.High supply voltage levels, improper braking parameters, or faulty overvoltage protection settings.Check supply voltage levels, verify braking conditions, and inspect the overvoltage protection settings in the drive parameters.
F005Field current failureThe motor field current has dropped below the minimum threshold.Loose field wiring connections, low field supply voltage, or a fault on the field controller board.Check field wiring connections, verify field supply voltage, and inspect the field controller board for faults.
F011Tacho or speed feedback faultThe speed feedback signal is missing or out of range.Faulty tachogenerator or encoder wiring, lost feedback signal, or incorrect parameterization.Check tachogenerator or encoder wiring, verify feedback signal levels, and confirm correct parameterization of the feedback channel.
F015OvertemperatureThe drive or power section has exceeded the permissible operating temperature.Inoperative cooling fan, excessive ambient temperature, or blocked ventilation clearances.Check cooling fan operation, verify ambient temperature is within specification, and ensure ventilation clearances are maintained.
F025Phase failureOne or more supply phases are missing or have an asymmetry.Missing incoming supply phase, blown input fuse, or unbalanced supply voltage.Check incoming supply connections, verify fuses on all three phases, and inspect supply voltage balance.
F035Communication faultSerial interface or board communication has failed.Unseated board, damaged backplane connector or pins, parameter mismatch, or board hardware fault.Check board seating and connector integrity, verify communication interface parameters, and reseat or replace the affected board if necessary.
A050Alarm: Current controller at limitThe current controller has reached its output limit.Mechanical motor overload, incorrect current limit parameters, or abnormal armature circuit resistance.Check for mechanical motor overload, verify current limit parameters, and inspect the armature circuit for abnormal resistance.

Frequently Asked Questions

What is the Siemens C98043-A7001-L2-4?

It is an internal CUD1 electronic control module assembly with terminal for Siemens SIMOREG DC MASTER 6RA70 series converters. It supports internal control and armature and field current regulation functions.

What must match when replacing this SIMOREG control board?

The installed drive series and L2-4 hardware variant must match, including internal wiring, terminal configuration, connector arrangement and firmware requirements.

How are SIMOREG parameters restored after replacement?

Parameters can be restored or re-entered using an OP1S operator panel, DriveMonitor or SIMOVIS software. Parameterization and commissioning are required after installation.

Where are SIMOREG 6RA70 faults and alarms displayed?

Faults and alarms can be read on the SIMOREG 6RA70 PMU or OP1S keypad display. DriveMonitor and SIMOVIS also support diagnostics and troubleshooting.

What should be checked for a communication fault F035?

Check board seating, the backplane connector and pins, and the communication interface parameters. The affected board may need to be reseated or replaced.

Take advantage of our exchange formula

A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.

Play it safe with our warranty conditions

Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.​​​​​​​

Data backup and recovery

Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.

Specific firmware and hardware versions

If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.


Disclaimer:
We are not an authorised distributor of Siemens.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.