Siemens 6RA7085-6FV62-0-Z SIMOREG DC MASTER DC Converter

New 
On request
Refurbished   
On request
Want to exchange a faulty product?
Receive a discount on your purchase when you turn in a faulty product. Upon receipt, we will check the product to determine its eligibility according to the terms and conditions.
Repair  
Available
We can repair this product for you.
 

Product Information

Product Family: SIMOREG DC MASTER 6RA70

The Siemens 6RA7085-6FV62-0-Z is a SIMOREG DC MASTER digital DC converter and 4-quadrant DC motor controller for high-power industrial drive systems. It provides fully digital, microprocessor-controlled operation for motoring and regenerative braking in both directions through a B6A-B6C antiparallel bridge. The converter accepts a 460 V AC, 3-phase supply and provides a 600 A DC rated armature output, with an integrated D480/600 field rectifier for DC motor field excitation.

This configured SIMOREG DC MASTER 6RA70 unit includes the G94, D64, S00, K01 and K11 options. S00 supports freely programmable technology functions such as winder control and positioning, with activation dependent on a PIN associated with the individual unit serial number. K01 and K11 provide EB1 and EB2 terminal expansion. Replacement commissioning can be performed with Siemens DriveMonitor, while an optional OP1S operator panel supports parameterization, monitoring and parameter upload or download through RS-485. Parameters are stored in internal non-volatile EEPROM, including user and factory parameter sets, so configuration transfer and compatibility checks are important before putting a spare into service.

For troubleshooting, the converter provides a PMU seven-segment display on the CUD1 control board, with additional monitoring through OP1S and DriveMonitor. Fault and warning displays use Fxxx and Axxx formats; diagnostic parameters r047 and r049 provide the fault code and fault value. When replacing a unit, check the installed SIMOREG 6RA70 system, firmware, motor and field requirements, and the G94, D64, S00, K01 and K11 option configuration. The discontinued Siemens converter is suited to repair, exchange and retrofit requirements in existing DC drive installations.

Technical Specifications

ManufacturerSiemens
Part number6RA7085-6FV62-0-Z
Model/typeSIMOREG DC MASTER digital DC converter
Product familySIMOREG DC MASTER 6RA70
Component type4-quadrant DC motor controller
Supply voltage460 V AC, 3-phase
Rated DC armature current600 A DC
Rated input current498 A AC
Field rectifierIntegrated D480/600 field rectifier
Control methodFully digital, microprocessor-controlled 4-quadrant operation
Power circuitB6A-B6C antiparallel 4-quadrant bridge
Operator panel connectionOptional OP1S operator panel via RS-485
Terminal expansionEB1 and EB2 terminal expansion included through options K01 and K11
Technology functionsFreely programmable technology functions through option S00; serial-number-dependent PIN enablement required
Parameter storageInternal non-volatile EEPROM with user and factory parameter sets
Option configurationG94+D64+S00+K01+K11
Lifecycle statusDiscontinued by Siemens

Programming and Configuration

Siemens DriveMonitor supports parameterization, commissioning, monitoring and parameter transfer for the 6RA7085-6FV62-0-Z. The optional OP1S operator panel provides an alternative interface for parameterization, monitoring, and parameter upload or download through an RS-485 connection.

The converter stores parameters in internal non-volatile EEPROM and supports user and factory parameter sets. During replacement work, transfer the required parameter set and confirm that the firmware, motor and field requirements, option configuration and installed SIMOREG 6RA70 system are compatible.

Option S00 provides freely programmable technology functions, including winder control and positioning. Enabling these functions requires a PIN associated with the individual unit serial number, so the S00 requirement should be resolved as part of commissioning preparation.

Communication and System Integration

The optional Siemens OP1S operator panel connects to the converter through RS-485 and supports parameterization, monitoring, and parameter upload or download. Siemens DriveMonitor provides the software interface for commissioning, parameter management and diagnostics.

The configured unit includes K01 and K11, providing EB1 and EB2 terminal expansion for additional connection flexibility. System integration and replacement checks should include the existing SIMOREG DC MASTER 6RA70 installation, the installed option package, the firmware and the field circuit requirements.

Diagnostics and Status Indication

The CUD1 control board includes a PMU seven-segment display for local status and fault indication. The optional OP1S operator panel and Siemens DriveMonitor provide additional parameter monitoring and diagnostic access during commissioning and service work.

Fault and warning displays use Fxxx and Axxx code formats. Diagnostic parameter r047 provides the fault code and r049 provides the fault value. Parameter upload and download through DriveMonitor or OP1S can support configuration recovery and comparison during replacement troubleshooting.

For a failed or exchanged converter, first compare the installed motor and field requirements, firmware and option configuration with the replacement unit. Confirm the G94, D64, S00, K01 and K11 configuration and resolve the S00 serial-number-dependent PIN requirement before commissioning.

Replacement and Spare Part Considerations

The Siemens 6RA7085-6FV62-0-Z is a discontinued SIMOREG DC MASTER 6RA70 converter intended for replacement, repair, exchange and retrofit work in existing industrial DC drive installations. The replacement must match the required 460 V AC, 3-phase supply, 600 A DC rated armature output, integrated D480/600 field rectifier and the installed motor and field circuit requirements.

Verify the complete configured order code, including G94, D64, S00, K01 and K11, before installation. Firmware compatibility, terminal expansion, technology functions and the S00 PIN requirement can affect whether the replacement can be commissioned in the existing system.

Use DriveMonitor or OP1S to transfer the required parameters from the existing installation when possible. Because the converter is part of a four-quadrant DC drive system, commissioning should include configuration transfer and checks of the motor, field circuit and installed SIMOREG 6RA70 system rather than treating the spare as a plug-in replacement.

Frequently Asked Questions

What is the Siemens 6RA7085-6FV62-0-Z?

It is a SIMOREG DC MASTER 6RA70 digital DC converter and 4-quadrant DC motor controller with a 600 A DC rated armature output, a 460 V AC, 3-phase supply and an integrated D480/600 field rectifier.

Which options are included in this SIMOREG converter?

The configured unit includes G94, D64, S00, K01 and K11. K01 and K11 provide EB1 and EB2 terminal expansion, while S00 supports freely programmable technology functions.

How is the 6RA7085-6FV62-0-Z configured during replacement?

Siemens DriveMonitor or an optional OP1S operator panel can be used for parameterization and parameter upload or download. Parameters are stored in internal non-volatile EEPROM with user and factory parameter sets.

Does the S00 option require additional enablement?

Yes. S00 technology functions require a PIN associated with the individual unit serial number. This requirement should be resolved before commissioning functions such as winder control or positioning.

How are faults and warnings displayed?

The PMU seven-segment display on the CUD1 control board shows local status and fault information. OP1S and DriveMonitor provide additional monitoring, while fault and warning formats use Fxxx and Axxx codes. Diagnostic parameters r047 and r049 provide the fault code and fault value.

What should be checked before ordering a replacement?

Check the SIMOREG DC MASTER 6RA70 system, 460 V AC, 3-phase supply, motor and field requirements, firmware, the complete G94+D64+S00+K01+K11 option configuration and the S00 PIN requirement.

Take advantage of our exchange formula

A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.

Play it safe with our warranty conditions

Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.​​​​​​​

Data backup and recovery

Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.

Specific firmware and hardware versions

If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.


Disclaimer:
We are not an authorised distributor of Siemens.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.