SEW Eurodrive 08268355 MCF41A0015-5A3-4-00 MOVIDRIVE Frequency Inverter 1.5kW

Het item werd toegevoegd aan uw offerteaanvraag
Product Information
The SEW Eurodrive 08268355, model MCF41A0015-5A3-4-00, is a 1.5 kW frequency inverter belonging to the MOVIDRIVE compact family. Engineered for controlling 3-phase AC asynchronous motors without encoder feedback, this unit operates across a primary supply voltage range of 380 V to 500 V AC at 50/60 Hz. The drive delivers a rated output current of 4.0 A, with a maximum continuous output current of 5.0 A and a peak current capability of 6.4 A over an output frequency range of 0 to 600 Hz. Speed and torque regulation are governed by SEW Eurodrive's Voltage Flux Control (VFC) technology. To support dynamic braking applications, the inverter features full 4-quadrant operating capability and an integrated braking chopper designed to handle regenerative energy during rapid deceleration.
Network integration and parameterization are served by multiple onboard communication pathways. The MCF41A variant includes a built-in PROFIBUS DP fieldbus interface via a DB-9 connector supporting speeds up to 12 Mbps, a CAN-based SBus system bus operating at 1 Mbps, and an RS-485 serial port utilizing MOVILINK protocol at 9.6 kbps. Physical control interfacing consists of 7 digital inputs (6 programmable and 1 dedicated enable), 2 binary outputs, 1 fault changeover relay, and differential analog I/O points. Commissioning a replacement unit requires restoring drive parameters and any embedded IPOSplus sequence control programs using MOVITOOLS software (version 3.0 or higher) or a DBG11A/DBG11B keypad via USB11A or UBG11A adapters. Station addresses must also be configured via onboard DIP switches. ABC Industrial Parts can assist maintenance teams with parameter backup extraction and pre-commissioning readiness when setting up replacement hardware.
Status monitoring and diagnostic readouts are centered on the red 7-segment front display, which presents operating conditions such as '0' (Inverter not ready), '1' (Controller inhibit), '2' (No enable), '3' (Drive enabled), 'A' (Technology option active), and flashing 'F' error codes during fault events. Diagnostic records store the last four fault events complete with operating data, accessible through MOVITOOLS Scope/Shell software or the DBG11B keypad menu. Initial field checks should cover 3-phase line supply balance, motor wiring insulation, braking resistor connections, and fieldbus cable termination. Internal microprocessor, memory, or output stage failures—such as System Faults 17 through 19 or persistent EEPROM errors—are internal hardware issues that cannot be serviced in the field. Under these conditions, unit repair or replacing the component with a tested spare from ABC Industrial Parts provides the direct route back to full operation.
Technical Specifications
| Manufacturer | SEW Eurodrive |
| Part Number | 08268355 |
| Model / Type | MCF41A0015-5A3-4-00 |
| Product Family | MOVIDRIVE compact |
| Component Type | Frequency Inverter |
| Rated Power Output | 1.5 kW |
| Supply Voltage Range | 380 - 500 V AC |
| Supply Frequency | 50/60 Hz |
| Rated Output Current | 4.0 A |
| Maximum Continuous Output Current | 5.0 A |
| Peak Output Current | 6.4 A |
| Output Frequency Range | 0 - 600 Hz |
| Control Mode | Voltage Flux Control (VFC) |
| Operating Quadrants | 4-Quadrant with integrated braking chopper |
| Fieldbus Interface | PROFIBUS DP (Integrated, 12 Mbps) |
| System Bus Interface | SBus (CAN, 1 Mbps) |
| Serial Interface | RS-485 (MOVILINK, 9.6 kbps) |
| Digital Inputs | 7 (6 Programmable + 1 Fixed Enable) |
| Digital Outputs | 2 Binary (0/24 V) |
| Relay Output | 1 Fault Changeover Relay (NO/NC/COM) |
| Analog Inputs | 1 Differential (+/-10V, 0-10V, 0/4-20mA) |
| Analog Outputs | 1 (+/-10V, 0-10V, 0/4-20mA) |
Programming and Configuration
Parameter setting and drive configuration for the SEW Eurodrive 08268355 frequency inverter are performed using MOVITOOLS software (Version 3.0 or higher) or directly using DBG11A and DBG11B operator keypads. Communication between the host commissioning PC and the drive is established through the RS-485 interface via MOVILINK protocol, requiring hardware interface adapters such as the USB11A or UBG11A. Software tools like MOVITOOLS Shell enable comprehensive parameter editing, real-time oscilloscope tracking via MOVITOOLS Scope, and drive operation checks during setup.
In addition to standard drive control parameterization, the unit supports integrated IPOSplus logic and positioning control. IPOSplus enables users to run localized control programs directly within the drive inverter, executing motion sequences and positioning tasks while offloading processing tasks from the primary PLC master. Complete parameter sets and custom IPOSplus programs can be archived on a PC or copied directly into the internal EEPROM of a DBG11B keypad for parameter replication across replacement units.
Communication and System Integration
System connectivity is natively provided on the MCF41A0015-5A3-4-00 via its integrated PROFIBUS DP slave interface. Supporting fieldbus communication speeds up to 12 Mbps using a standard DB-9 connection, the drive integrates directly into PROFIBUS network topologies. Station addressing is configured via DIP switches located on the inverter hardware, establishing cyclic process data transmission with central host controllers.
Auxiliary communications include an integrated CAN-based SBus system bus operating at speeds up to 1 Mbps and an RS-485 serial connection running MOVILINK protocol at 9.6 kbps. Local hardware integration is supported by 7 digital inputs (including fixed controller enable DI00), 2 binary outputs (0/24 V), 1 fault changeover relay, 1 differential analog input, and 1 analog output configured for standard voltage (+/-10V, 0-10V) or current (0/4-20mA) signals.
Diagnostics and Status Indication
Operational status and error messages are displayed directly on the unit's red 7-segment display. Single alphanumeric characters indicate real-time states, allowing maintenance staff to quickly distinguish between normal operation, missing enable signals, or active technological options.
For advanced troubleshooting, the drive stores a fault history log containing the last 4 fault events alongside critical operating data. Comprehensive diagnostic evaluations can be performed remotely over PROFIBUS DP via fieldbus diagnostic status words, locally using the DBG11B keypad diagnostic menu, or through graphical trace functions in MOVITOOLS.
Status LED Indicators
| LED | Color/Status | Meaning |
|---|---|---|
| 7-Segment Display | Red - 7-Segment Readout | Displays operating status codes: '0' (Inverter not ready), '1' (Controller inhibit), '2' (No enable), '3' (Drive enabled), 'A' (Technology option active), 'F' (Fault mode - flashes fault code) |
Replacement and Spare Part Considerations
When selecting a replacement for an existing installation, match both the part number 08268355 and model code MCF41A0015-5A3-4-00. The MCF designation indicates standard integrated PROFIBUS DP fieldbus support, which is mandatory for applications relying on cyclic PROFIBUS communication with a master PLC.
A replacement drive cannot run directly out of the box without configuration. Prior to placing the unit into operation, parameter settings and any stored IPOSplus positioning logic must be transferred from the original unit or project archives using MOVITOOLS (Version 3.0 or higher) or a DBG11B keypad. Additionally, verify that the PROFIBUS station address DIP switches and bus termination resistors on the replacement match the system network layout.
Error Codes & Fault Codes
The following error codes may be displayed during operation or diagnostics:
| Code | Name | Description | Possible Cause | Recommended Action |
|---|---|---|---|---|
| 01 | Overcurrent | Short circuit at output, motor power too large, or defective output stage. | Short circuit on motor lead, motor overload, defect in output power section. | Check motor wiring and insulation, reduce motor load, check drive sizing. If fault persists without motor connected, output stage is damaged requiring unit repair. |
| 03 | Ground Fault | Earth fault in motor circuit or inverter. | Ground fault in output lead or motor winding, internal ground fault. | Check motor cables and motor insulation resistance. If insulation is sound, internal drive hardware failure requires unit repair. |
| 04 | Brake Chopper | Excessive braking current or short circuit in brake chopper circuit. | Braking resistor shorted or too low resistance, internal brake chopper transistor defect. | Check braking resistor resistance and connection wiring. If resistor is correct, brake chopper is defective requiring unit repair. |
| 06 | Mains Phase Failure | One line phase missing in supply line. | Mains fuse blown, line phase unbalanced or lost. | Check AC supply line fuses and supply voltages. |
| 07 | DC Link Overvoltage | DC link voltage exceeded permissible maximum limit. | Excessive regenerative energy back-fed from motor, deceleration time too short, braking resistor open circuit. | Increase deceleration ramp time, check braking resistor value and cabling. |
| 08 | Speed Monitoring | Speed slip limits exceeded or speed control loop open. | Mechanical overload, output phase missing, incorrect motor parameter settings. | Check mechanical load, check output motor connections, verify motor parameter settings. |
| 09 | Inverter Utilization | Continuous thermal overload of the inverter (I2t limitation). | Inverter operated in current limit continuously. | Reduce drive load or increase acceleration/deceleration times. |
| 11 | Overtemperature Heatsink | Heatsink temperature exceeded threshold. | Insufficient cooling airflow, fan defective, ambient temperature too high. | Clean heatsink fins, verify internal cooling fan operation, ensure adequate cabinet ventilation. |
| 17 | System Fault 17 | Internal microprocessor fault / control electronics hardware error. | Control board malfunction or corruption. | Internal hardware failure — replace the unit or contact SEW service for return for repair. |
| 18 | System Fault 18 | Internal program logic / execution fault. | Control board firmware or ASIC error. | Internal hardware failure — return unit for repair. |
| 19 | System Fault 19 | Internal memory error. | RAM / Flash memory hardware failure. | Internal hardware failure — return unit for repair. |
| 25 | EEPROM Error | Read/write error accessing internal EEPROM parameters. | Corrupted parameter memory or defective EEPROM chip. | Perform factory reset and reload parameters. If error persists, internal hardware error requires service. |
| 26 | External Fault | Digital input terminal configured for external fault is triggered. | External safety circuit or monitoring sensor opened. | Check external fault condition and terminal wiring. |
| 28 | Fieldbus Timeout | Loss of cyclic communication over PROFIBUS DP interface. | Damaged fieldbus cable, disconnected bus connector, incorrect station address, PLC master stopped. | Check PROFIBUS cabling, line termination resistors, PROFIBUS station address DIP switches, and PLC master status. |
| 31 | Motor Overtemperature TF/TH | Motor thermistor (TF) or thermal switch (TH) activated. | Motor overheated due to sustained overload or poor motor ventilation. | Allow motor to cool, check motor load and cooling fan. |
| 37 | SBus Timeout | Communication timeout on System Bus (SBus). | Interrupted SBus connection or slave/master communication dropped. | Check SBus 2-wire connection and termination resistors. |
| 43 | RS485 Timeout | Communication timeout on RS-485 interface. | Serial cable disconnected or host PC stopped transmitting. | Check serial connection cable and software communication settings. |
| 81 | Start Condition Error | Drive start condition not satisfied during enable attempt. | Enable signal missing or conflicting control signals. | Check enable input (DI00) and controller inhibit terminal status. |
| 82 | Open Output Phase | One phase missing between inverter output and motor. | Broken cable phase or contactor open on output side. | Check output wiring and motor terminal connections. |
| 84 | Motor Thermal Overload | Calculated motor thermal load (I2t) exceeded threshold. | Motor operated at low speed with high load without forced cooling. | Reduce motor load or install external forced cooling fan on motor. |
Frequently Asked Questions
What software is needed to parameterize the SEW Eurodrive 08268355 drive?
The drive is parameterized using MOVITOOLS software (Version 3.0 or higher). Connection to a PC requires an RS-485 interface adapter such as the USB11A or UBG11A. Alternatively, basic parameter adjustments and backups can be performed directly using a DBG11A or DBG11B operator keypad.
Is the MCF41A0015-5A3-4-00 inverter a direct plug-and-play replacement?
No, a replacement unit requires configuration before operation. Motor parameters, application settings, IPOSplus control sequences, and the PROFIBUS DP station address DIP switches must be loaded and aligned with your system settings before running the motor.
What does a flashing 'F' on the 7-segment display mean?
A flashing 'F' on the red 7-segment readout indicates that the drive has tripped on a fault. The display will alternate between 'F' and the specific numerical fault code (such as '01' for Overcurrent or '28' for Fieldbus Timeout).
How do I troubleshoot a Fault 28 (Fieldbus Timeout)?
Fault 28 indicates a loss of cyclic PROFIBUS DP communication. Check the DB-9 fieldbus cable connections, verify that the line termination resistors are correctly set at network ends, confirm that the station address DIP switches match the PLC hardware configuration, and check that the master PLC is in RUN mode.
Does this drive support dynamic braking for high-inertia loads?
Yes, the MCF41A0015-5A3-4-00 operates in 4 quadrants and includes an internal braking chopper transistor. To enable regenerative energy dissipation during deceleration, connect an appropriately sized external braking resistor across the designated drive terminals.
Take advantage of our exchange formula
A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.
Play it safe with our warranty conditions
Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.
Data backup and recovery
Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.
Specific firmware and hardware versions
If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.
Disclaimer:
We are not an authorised distributor of SEW Eurodrive.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.



