Key Technology 621203 REOVIB MFS268XXLH Vibratory Feeder Controller
Het item werd toegevoegd aan uw offerteaanvraag
Product Information
The Key Technology 621203 is a REOVIB MFS268XXLH vibratory feeder frequency controller for electromagnetic feeders used in conveying and dosing equipment. It regulates feeder frequency and output voltage to support controlled product flow. The controller operates from a 110-240 V AC supply at 50/60 Hz and provides a configurable output range of 0-205 V AC, with a 0-100 V AC range available depending on the input and configuration. Its integrated display and keypad support parameter programming, setpoint adjustment and operating-mode selection.
Before commissioning a replacement, match the feeder voltage and current requirements, wiring and connector assignments. Main power is connected at terminal block X0, while the feeder drive coil connects at X1. X4 supports track control, X6 provides the +24 V enable control signal, X5 provides ON/OFF and timeout status, and X40 accepts acceleration-sensor feedback for closed-loop control. Setpoints can be supplied through 0-10 V DC, 0/4-20 mA or an external 10 kOhm potentiometer. Two configurable parameter sets are stored in internal non-volatile EEPROM memory, so the replacement must be configured for the installed feeder and operating requirements.
For commissioning and troubleshooting, use the integrated display to review parameter menus and the system operating state, and use the keypad to adjust parameters or select the operating mode. Check the 110-240 V AC supply, the X0 and X1 wiring, the X4 and X6 control connections, the X5 ON/OFF and timeout signal, and the X40 acceleration-sensor connection where fitted. Also verify that the feeder requirements and connector assignments match the Key Technology 621203 REOVIB MFS268XXLH controller before returning the machine to service. ABC Industrial Parts can support repair or exchange preparation when configuration and wiring need to be matched to the replacement unit.
Technical Specifications
| Manufacturer | Key Technology |
| Part number | 621203 |
| Model/type | REOVIB MFS268XXLH |
| Product family | REOVIB MFS 268 |
| Component type | Vibratory feeder frequency controller |
| Supply voltage range | 110-240 V AC |
| Supply voltage tolerance | +/-10% |
| Supply frequency | 50/60 Hz |
| Output voltage range | 0-205 V AC |
| Alternative output voltage range | 0-100 V AC |
| Soft-stop time | 0-5 s |
| Analog setpoint input | 0-10 V DC |
| Analog current setpoint input | 0/4-20 mA |
| Potentiometer setpoint input | 10 kOhm |
| Main power input | Terminal block X0; L, N, PE |
| Feeder output | Terminal block X1; A1, A2, screen, PE |
| Track control input | Connector X4; +24 V, input, GND |
| Enable input | Connector X6; +24 V control signal |
| Status output | Connector X5; ON/OFF and timeout signal |
| Acceleration sensor input | Connector X40; closed-loop feedback |
| Parameter storage | Two parameter sets in internal EEPROM |
Programming and Configuration
Parameter programming is performed through the integrated display and keypad. The display provides access to parameter menus and the system operating state, while the keypad supports parameter adjustment, setpoint adjustment and operating-mode selection.
The controller stores two configurable parameter sets in internal non-volatile EEPROM memory. These sets support different coarse and fine control requirements and should be matched to the installed feeder and its operating conditions during replacement commissioning.
External setpoint control can be configured for a 0-10 V DC signal, a 0/4-20 mA current loop or an external 10 kOhm potentiometer. The soft-stop time is adjustable from 0-5 s, and the selected output range depends on the input and system configuration.
Communication and System Integration
The REOVIB MFS268XXLH integrates with feeder and automation wiring through defined terminal blocks and connectors. Terminal block X0 is used for main power with L, N and PE connections, while terminal block X1 connects the feeder drive coil through A1, A2, screen and PE.
Connector X4 provides track-control connections for +24 V, input and GND. Connector X6 accepts the +24 V remote enable control signal. Connector X5 supplies ON/OFF and timeout status information for connection to the machine control system.
Connector X40 accepts acceleration-sensor feedback for closed-loop feeder control. External feed-rate commands are supported through 0-10 V DC, 0/4-20 mA or a 10 kOhm potentiometer, allowing integration with analog automation and process-control signals.
Diagnostics and Status Indication
The integrated display provides a readout of parameter menus and the system operating state. The keypad allows the technician to review settings, adjust the setpoint and select the operating mode during commissioning or troubleshooting.
The ON/OFF and timeout status output is available through connector X5. For a replacement unit, check the supply at X0, feeder wiring at X1, control connections at X4 and X6, the X5 status connection and the X40 acceleration-sensor connection where closed-loop feedback is used.
Replacement and Spare Part Considerations
The exact replacement identity is Key Technology part number 621203, model REOVIB MFS268XXLH, from the REOVIB MFS 268 product family. Before fitting a spare, compare the part number, feeder voltage and current requirements, output range, connector assignments and wiring for X0, X1, X4, X5, X6 and X40.
A replacement requires configuration through the integrated display and keypad. Check the selected analog setpoint method, stored parameter sets, soft-stop setting, operating mode and acceleration-feedback arrangement before enabling the feeder. The output range can be 0-205 V AC or 0-100 V AC depending on the input and configuration.
ABC Industrial Parts can assist with repair or exchange preparation where the spare must be matched to existing feeder wiring and parameters. Confirming the feeder and control connections before energizing the replacement helps prevent commissioning delays.
Frequently Asked Questions
What is the Key Technology 621203?
The Key Technology 621203 is a REOVIB MFS268XXLH frequency controller for electromagnetic vibratory feeders used in conveying and dosing equipment.
What supply voltage does the REOVIB MFS268XXLH use?
The controller operates from 110-240 V AC at 50/60 Hz with a supply voltage tolerance of +/-10%.
Which setpoint signals are supported?
The controller supports a 0-10 V DC signal, a 0/4-20 mA current loop or an external 10 kOhm potentiometer.
Which connections must be checked during replacement?
Check terminal block X0 for main power, X1 for the feeder drive coil, X4 for track control, X6 for the +24 V enable signal, X5 for ON/OFF and timeout status, and X40 for acceleration-sensor feedback.
How are parameters configured on the 621203?
Parameters, setpoints and operating modes are adjusted with the integrated display and keypad. Two configurable parameter sets are stored in internal non-volatile EEPROM memory.
How can the controller be checked during troubleshooting?
Review the system operating state and parameter menus on the integrated display, then check the supply, feeder wiring, control connections, status output and acceleration-sensor connection where used.
Take advantage of our exchange formula
A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.
Play it safe with our warranty conditions
Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.
Data backup and recovery
Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.
Specific firmware and hardware versions
If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.
Disclaimer:
We are not an authorised distributor of Key Technology.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.