Elau 13130247 MC-4/11/10/400 Servo Drive Amplifier

New 
On request
Refurbished   
On request
Want to exchange a faulty product?
Receive a discount on your purchase when you turn in a faulty product. Upon receipt, we will check the product to determine its eligibility according to the terms and conditions.
Repair  
Available
We can repair this product for you.
 

Product Information

Product Family: PacDrive M | Series: MC-4

The Elau 13130247, model MC-4/11/10/400, is a digital servo drive amplifier for Elau PacDrive M motion control systems. It provides decentralized axis control within a centralized controller architecture, allowing coordinated positioning, acceleration, synchronization and speed regulation of compatible servo motors. The drive accepts a 380–480 V AC three-phase supply, provides 10 A continuous output current and supports an output frequency range of 0–600 Hz.

A replacement drive must match the installed PacDrive M system, motor and encoder combination, holding-brake configuration, project parameters and firmware compatibility. The unit also requires a separate 24 V DC control supply with a specified control current of 1 A. Before commissioning an Elau 13130247 spare, verify the mains supply, control voltage, motor-drive combination and established axis configuration. Schneider Electric VDM01D10AA00 and VDM01D10AQ00 are associated cross-reference candidates, but the correct designator must be confirmed for the installation.

The MC-4/11/10/400 uses SERCOS motion communication and can report conditions including control voltage outside range, DC bus overvoltage, following error, an unsupported motor-drive combination and SERCOS communication fault. First-line checks include measuring the 24 V DC supply at the drive terminals, checking mains voltage and braking-resistor wiring, reviewing motion and cam data, verifying motor and encoder settings, and inspecting the SERCOS optical connection. As a discontinued PacDrive M component, this servo amplifier is relevant for repair, tested exchange and replacement of established packaging, converting and material-handling machinery.

Technical Specifications

ManufacturerElau
Part number13130247
Model/typeMC-4/11/10/400
Component typeServo drive amplifier
Product familyPacDrive M
SeriesMC-4
Supply voltage380–480 V AC, 3-phase
Rated input current10.2 A
Continuous output current10 A
Output voltage0–480 V AC, 3-phase
Output frequency0–600 Hz
Control voltage24 V DC
Control current1 A
Rated power5 kW
Motion control interfaceSERCOS optical fieldbus
Communication protocolSERCOS
LifecycleDiscontinued

Communication and System Integration

The Elau MC-4/11/10/400 integrates into PacDrive M motion control architectures through a built-in real-time SERCOS optical fieldbus interface. In this arrangement, the centralized automation controller coordinates multiple decentralized servo drives for synchronized machine movements.

When replacing the drive, the SERCOS connection, motor and encoder configuration, project parameters and firmware compatibility must match the existing axis configuration. Inspect the optical cables and connectors during commissioning, particularly where a communication fault or lost telegrams is present.

Replacement and Spare Part Considerations

The Elau 13130247 is a discontinued servo drive amplifier for existing PacDrive M installations. Confirm the complete identification before ordering a spare: manufacturer Elau, part number 13130247 and model MC-4/11/10/400. The electrical match includes the 380–480 V AC three-phase supply, 10 A continuous output current, 24 V DC control supply and SERCOS communication interface.

Compatibility also depends on the installed motor, encoder, holding brake, project configuration and firmware. Cross-reference candidates VDM01D10AA00 and VDM01D10AQ00 require confirmation against the machine and axis configuration before use. After installation, check the control supply, mains voltage, motor and encoder settings, braking circuit and SERCOS optical connection before returning the machine to operation.

Error Codes & Fault Codes

The following error codes may be displayed during operation or diagnostics:

CodeNameDescriptionPossible CauseRecommended Action
Control voltage outside rangeControl voltage outside rangeThe 24 V DC control supply voltage is too high or too low.Faulty 24 V DC power supply, loose terminals, wiring problems, or unstable supply voltage.Measure the 24 V DC supply directly at the drive terminals. Inspect the power supply, wiring, and terminal connections, then restore the voltage to the permitted range.
DC bus overvoltageDC bus overvoltageThe DC bus voltage exceeds allowable operating limits.Excessive regenerative energy during deceleration, a missing or incorrectly wired braking resistor, or excessive incoming mains voltage.Check the mains voltage, braking resistor wiring, and resistance value. Increase the deceleration ramp time if the dynamic braking capacity is exceeded.
Following errorFollowing errorAxis position deviation exceeds the permitted following-error limit.Incompatible motion profile or cam data, or an incorrect Pos_P_Gain setting when operating in speed-control mode.Check the motion profile and cam data. For speed-control operation, verify the Pos_P_Gain parameter and adjust it or set it to 0 as required.
Motor-drive combination not supported / Invalid motorMotor-drive combination not supportedThe servo drive rejected the connected motor type or encoder configuration.Unsupported encoder interface, incompatible motor, holding-brake, and drive combination, configuration mismatch, or corrupted encoder data.Verify the motor model, encoder type, project configuration, and firmware compatibility. Use only manufacturer-approved motor-drive combinations.
Sercos communication faultSERCOS communication faultA temporary signal disturbance or lost telegrams occurred on the SERCOS optical communication bus.Disturbed fiber-optic cables, damaged connectors, improper shielding, poor cable routing, or electrical noise in the control cabinet.Inspect SERCOS optical cables, connectors, shielding, and routing. Eliminate EMC noise sources in the control cabinet before replacing the drive.

Frequently Asked Questions

What is the Elau 13130247 MC-4/11/10/400?

It is a PacDrive M servo drive amplifier for decentralized axis control. The unit provides 10 A continuous output current and communicates with the PacDrive controller through a real-time SERCOS optical fieldbus.

What electrical supply does this Elau servo drive require?

The drive accepts a 380–480 V AC three-phase supply and requires a separate 24 V DC control supply. The rated input current is 10.2 A and the control current is 1 A.

Can VDM01D10AA00 or VDM01D10AQ00 replace Elau 13130247?

VDM01D10AA00 and VDM01D10AQ00 are associated cross-reference candidates. The correct designator must be confirmed against the installed motor, encoder, holding-brake configuration, project parameters and firmware.

What should be checked before commissioning a replacement?

Check the mains voltage, 24 V DC control supply, motor and encoder combination, holding-brake configuration, project parameters, firmware compatibility, braking-resistor wiring and SERCOS optical connection.

What can cause a SERCOS communication fault?

Possible causes include disturbed fiber-optic cables, damaged connectors, improper shielding, poor cable routing and electrical noise in the control cabinet. Inspect the optical connection and eliminate EMC noise sources before replacing the drive.

Take advantage of our exchange formula

A defective product does not have to be worthless. At ABC Industrial Parts, you can hand in defective products and immediately benefit from a discount on your new purchase. This is a smart way to save money while contributing to a circular economy.

Play it safe with our warranty conditions

Industrial plants prefer to keep running invariably, no matter what. Therefore, it is essential that you can rely on high-quality products and/or sustainable repairs. With our warranty conditions, you can count on certainty, whether you choose new, used or repaired products.​​​​​​​

Data backup and recovery

Have you lost valuable parameters or data due to a malfunction while the manufacturer no longer provides support? At ABC Industrial Parts, we help you secure this data, both for common and specific products.

Specific firmware and hardware versions

If you are working with specific hardware or firmware versions that are no longer available from the manufacturer, ABC Industrial Parts is your partner. When making your enquiry, clearly state which versions you need, we will then look at the possibilities of supplying those versions, so that your installations continue to function optimally.


Disclaimer:
We are not an authorised distributor of Elau.
Product photos are for illustration purposes only and may differ from the actual product delivered.
Some of the content on this page was created with the help of AI. While we strive to provide accurate and up-to-date information, errors may occur.